TJC STEEL.
  • Home
  • Product
  • Contact
  • About
  • News

Inconel 718 Alloy- TJC STEEL.

12/9/2020

 
Inconel 718 alloy is a precipitation-hardened nickel-chromium alloy containing niobium and molybdenum. It has high strength, good toughness and corrosion resistance in high and low temperature environment under 650℃.Its state [TJC STEEL.]may be solid solution treatment or precipitation hardened state.

Introduction for Inconel 718 Alloy:

Characteristics:
● Machinability
● High tensile strength, fatigue strength, creep strength and fracture strength at 700℃
● High oxidation resistance at 1000℃
● Stable chemical properties at low temperature
● Good welding performance

Application:
Due to its high temperature strength, excellent corrosion resistance and easy processing at 700℃, it can be widely used in various demanding occasions.● Liquid fuel rocket
● Low temperature engineering
● Acidic environment

Second-ranking Nuclear Engineering
Standards and Equivalent Materials with Inconel 718 Alloy:
GH4169, GH169 (China), NC19FeNb (France), NiCr19Fe19Nb5, Mo3(Germany), [TJC STEEL.]NA 51 (UK) Inconel718, UNS NO7718(USA) NiCr19Nb5Mo3(ISO)

Chemical Composition(%):
镍Ni - 铬Cr - 铁Fe - 碳C - 锰Mn - 硅Si - 钼Mo - 铜Cu - 钴Co - 铝Al - 钛Ti - 铌Nb - 硼B - 磷P - 硫S
Min 50 - 17 - - - - - 2.8 - - - 0.2 - 0.65 - 4.75 - 0 - -
Max 55 - 21 - 余量 - 0.08 - 0.35 - 0.35 - 3.3 - 0.3 - 1 - 0.8 - 1.15 - 5.5 - 0.006 - 0.01 -
0.01

Mechanical Property for Inconel 718 Alloy:
Density for Inconel 718 Alloy:
Rho = 8.24 g/cm3 density
Melting Temperature Range
The melting temperature ranges from 1260 ℃ to 1320℃
Processing and heat treatment editing
Inconel718 alloy is a difficult material in machining field.

Preheating:
Surfaces must be cleaned before and during heating to keep surfaces clean.Inconel718 alloy will become brittle if the heating environment contains sulfur, phosphorus, lead or other low melting point metals.Impurities come [TJC STEEL.]from marking paint, chalk, lubricating oil, water, fuel, etc.The sulfur content of fuel should be low, such as the impurity content of liquefied natural gas and natural gas should be less than 0.1%, the sulfur content of urban gas should be less than 0.25g/m3, the sulfur content of LPG should be less than 0.5% is ideal.
Electric furnace heating had better have more accurate temperature control ability, furnace gas must be neutral or weak alkaline, should avoid furnace gas composition in oxidation and reduction in fluctuation.

Hot Working:
The suitable hot working temperature of Inconel718 alloy is 1120-900℃. The cooling way can be water quenching or other rapid cooling way. After hot working, annealing should be timely to ensure the best performance.The material [TJC STEEL.]should be heated to the upper limit of the processing temperature during thermal processing. In order to ensure the plasticity during processing, the final processing temperature should not be lower than 960℃ when the deformation amount reaches 20%.

Cold Working
Cold working should be carried out after solid solution treatment, the working hardening rate of Inconel718 is higher than austenitic stainless steel, so the processing equipment should be adjusted accordingly, and there should be an intermediate annealing process in the cold working process.

Heat Treatment
Different solid solution treatment and aging treatment process can obtain different material properties.Due to the low diffusion rate of phase, the best mechanical properties of Inconel718 alloy can be obtained by aging treatment for a long time.

Polishing
The oxides near the welds of the Inconel718 workpieces are more difficult to remove than those of stainless steel, which need to be polished with a fine sand belt, and the oxides also need to be removed with sandpaper or pre-treated in a salt bath before pickling in a mixture of nitric and hydrofluoric acids.

Machining
The Inconel718 is machined after solution treatment, taking into account the material's work hardening properties. Unlike austenitic stainless steels, the Inconel718 is suitable for low surface cutting speeds.

Welding
Precipitation-hardened Inconel718 alloys are well suited for welding and have no post-weld cracking tendency.Weldability, machinability and high strength are the advantages of this material.
Inconel718 is suitable for arc welding, plasma welding, etc.Before welding, the surface of the material shall be clean, free from oil stains, chalk marks, etc., and the polished metal shall be exposed within 25mm around the weld.

Recommended Welding Materials for Inconel 718:
GTAW/GMAW
Nicrofer S 5219
W. - Nr. 2.4667
SG-NiCr19NbMoTi
AWS ERNiFeCr 5.14-2 A
BS 2901 Part 5: NA 51

Comments are closed.

      TJC Steel News Center

    Company News, Market News and Order Cases About TJC Steel.

    Archives

    April 2025
    December 2024
    October 2024
    September 2024
    July 2024
    June 2024
    May 2024
    April 2024
    March 2024
    February 2024
    January 2024
    December 2023
    November 2023
    September 2023
    August 2023
    July 2023
    June 2023
    April 2023
    March 2023
    February 2023
    January 2023
    December 2022
    November 2022
    September 2022
    July 2022
    May 2022
    March 2022
    February 2022
    January 2022
    December 2021
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    June 2021
    April 2021
    March 2021
    February 2021
    January 2021
    December 2020
    November 2020
    July 2020
    June 2020
    May 2020
    April 2020
    March 2020
    February 2020
    January 2020
    December 2019
    November 2019
    October 2019
    September 2019
    May 2019
    April 2019
    January 2019
    December 2018
    October 2018
    September 2018
    August 2018

    Categories

    All
    Stainless Coils/ Sheets
    Steel PIpe
    Steel Plates

    RSS Feed

HOME

ABOUT

PRODUCT

NEWS

CONTACT

TJC IRON& STEEL CO.,LTD
Tel:+86-371-86107816; +8613674998777 Email: [email protected]
HENAN SCALE IMP&EXP CO.,LTD
ZHENGZHOU ZHIYUAN IMP&EXP CO.,LTD
Copyright © 2015
  • Home
  • Product
  • Contact
  • About
  • News